{"product_id":"perun-mosfet-for-krytac-kriss-vector","title":"Perun MOSFET for KRYTAC Kriss Vector","description":"\u003cp\u003e\u003cmeta charset=\"UTF-8\"\u003e\u003cspan\u003ePerun for Krytac Kriss Vector replaces stock electronics in Kriss Vector airsoft replicas made by Krytac company.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eIt provides lots of additional features, including active braking and full cycle control (making sure that each cycle is finished, even if the trigger is pulled very briefly). \u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eFeature description:\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eFreely programmed firing modes\u003c\/strong\u003e\u003cspan\u003e\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eSet any firing mode you like on any of the selector positions independently. Available modes are: safe, semi, binary, 2 to 5 round burst and auto. \u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eActive brake\u003c\/strong\u003e\u003cspan\u003e\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eActive brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem). \u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003ePrecocking\u003c\/strong\u003e\u003cspan\u003e\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eFast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, piston will remain in rear position after each shot with the spring already compressed, ensuring that next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull and hold the trigger. A second shot will be fired after 3 seconds, with no precocking and fully braked. \u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eRate of fire reduction\u003c\/strong\u003e\u003cspan\u003e\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eReduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion. \u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eDMR mode\u003c\/strong\u003e\u003cspan\u003e\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eIntroduces intervals between semiautomatic shots to comply with DMR rules on some fields. \u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eLow battery voltage alarm\u003c\/strong\u003e\u003cspan\u003e\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eDedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off. \u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eDiagnostic system\u003c\/strong\u003e\u003cspan\u003e\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eConstantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier. \u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eElectronic fuse\u003c\/strong\u003e\u003cspan\u003e\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eWill save your replica and battery in case of a major malfunction. It will automatically disconnect the battery when a short circuit or blocked motor is detected. \u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eProgramming of all the settings is done solely by using quick and easily memorable sequences of fire selector switching and trigger pulls supported by sound signals and multicolor LED diode. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. \u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eAll settings are set independently for each selector position, so you can program the mosfet exactly the way you want, for example semi on semi and binary trigger on auto.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003ePerun for Krytac Kriss Vector works without problems with any battery from 7V do 17V. It can also be used with most extreme setups.\u003c\/span\u003e\u003c\/p\u003e","brand":"Evike","offers":[{"title":"Default Title","offer_id":41947435171898,"sku":"KV-XX-XX","price":94.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2513\/0626\/files\/Screenshot2026-11-18at12.30.31PM.png?v=1795023105","url":"https:\/\/blackopswebstore.com\/products\/perun-mosfet-for-krytac-kriss-vector","provider":"Black Ops Paintball","version":"1.0","type":"link"}